<noscript> <h1>customwholesaleblinds.com – Your Source for affordable, yet high quality Window Blinds and Shades. Check out this blinds site: <a href="http://www.customwholesaleblinds" target="_blank">CustomWholesaleBlinds.com</a> </h1><br><br> Find a room darkening pleated or cellular shades along with bamboo shades or woven woods. <p> We don't offer brands like Hunter Douglas Blinds, Levelor Blinds (levolor), Bali Blinds, Graber Blinds or other brand names. <br> NOTE: Our site requires that you have scripts and frames turned on. Thank you. <br> <div align="center"> <H1>customwholesaleblinds.com – Your Online Source for High Quality & Affordable Window Blinds & Shades</H1><H3>Online Selection of Window Blinds & Shades</H3> </div> </noscript>
Faux Wood Blinds * Vertical Blinds * Cellular Shades * Aluminum Blinds * Bamboo Blinds * Roman Shades * Sun Shades
customwholesaleblinds.com – Your Online Blinds Resource
Contact CustomWholesaleBlinds
Phone: 1-888-877-1860
Sales@customwholesaleblinds.com
Hours (eastern time):
Mon-Fri: 9:00am till 5:00pm
Sat-Sun: Closed

HOME  - LOGIN   - CONTACT US  -  MEASURING  -  FAQ  -  POLICIES  -  VIEW CART  -  ORDER STATUS  -  ABOUT US

Home »   Programming: 6 Channel Remote Control »

Programming: 6 Channel Remote Control


These 'Techniku' remote instructions are only intended for the remote that controls the motorized systems on our 1" wood blinds, 1/2" aluminum blinds, 2" aluminum blinds, 1/2" cellular shades and 3/4" cellular shades.

IMPORTANT: Some products may program in different ways. It is best to refer to each individual product's user manual. Program each blind/shade immediately after connecting the power source (batteries or power supply) at the window covering. Do NOT use the "P" button on the remote.
Step 1: Insert 2 "AAA" batteries in the proper orientation as shown in the battery case of the remote control.
Step 2: Decide which channel (1-6) you wish to program the blind/shade.
Step 3: Point the remote control at the receiver and press the selected channel mode first (buttons 1-6), followed by the "Channel" function (left or right arrow button) button. The blind/shade is now programmed to that channel. Do not press the "P" or "ALL" Channel first! If the "P" or "ALL" Channel is inadvertantly pressed during programming, see "Reprogramming the Remote Control Channel" below.
Operate Individual Channel: To operate the blind/shade on an individual channel mode (buttons 1-6), press the selected channel mode (buttons 1-6), followed by the "Channel" function (left or right arrow button) button. The blind/shade will operate from that channel only and will not respond to the other channels except "ALL."
Operate "ALL" Channels: To operate all of the blinds/shades within direct-line-of-sight, simply press either the up or down arrow button. The "ALL" channel does not need to be programmed separately.

Reprogramming the Remote Control Channel


If a blind/shade is not programmed to the desired channel, reprogramming is simple.
1. Disconnect the power source from the blind/shade of the covering that needs to be reprogrammed.
2. Leave the power source disconnected for approximately 15 minutes (up to 1 hour).
3. Reconnect the power source.
4. Program the blind/shade by pressing the button of the new desired channel mode (buttons 1-6) and the "Channel" function (left or right arrow) button. The blind/shade is now programmed to that channel.
5. The blind/shade can be reprogrammed as many times as necessary. The channel will also need to be reprogrammed after installing new batteries, or if using a power supply, when the standard house power goes out.


HOME  -  CONTACT US  -  MEASURING  -  FAQ  -  POLICIES  -  VIEW CART  -  ORDER STATUS  -  ABOUT US

5350 NW 165th St, Miami, Florida 33014   Phone: 1-888-877-1860   Email: CustomerService@customwholesaleblinds.com
Copyright - customwholesaleblinds.com    Home Decor Partners    Website Comments    Trade Organizations    Blinds 101